FROM THE DESK OF BILL PARR

Prototype Finished

2011-02-01T15:52:00.005-05:00

Prototype completed ... If you don't understand, go on the blog archive and open an earlier post, "another drain cleaning tool". Or if you want to see all tools just scroll down.

Total package as stored in truck!
Good for single bowl or multiple bowls.

Shown Below With Accessories:

Double hose connection 5', vacuum breaker [safe plumbing], support pipe, hose tread to aireator male/female adapter, plug in end so parts don't fall out and the last item chain stay? It is possible that the front end of the snake could weigh more than the tail end, especially when a couple of cables are vertical like in a 2nd floor entry. It is possible that when the snake is disconnected at the wall to install the
boot the snake could be pulled into the piping. If that were to occur then you would be pissed off at Parr. So the rule is secure the snake with the chain, personally I will have a small pair of locking pliers to hold the cable while it is vulnerable until I get the chain on. Using on a double bowl you won't need the 2nd bibb. On a single bowl water can be drawn from the faucet using the hose and vacuum breaker. Assume water will be entering through the branch on the wye. Water going in should drain away when the drain is properly opened. A lot of water coming from the 2nd bibb into a container would show an non-opened drain. In any event when finished the snake should come out clean. And you will only have removed and reinstalled
the trap one time. I am looking forward to learning from "DAS BOOT"
Happy drain opening! Caution this is not a tool for Stupid Users

Another drain cleaning tool ...

2011-01-30T09:47:00.002-05:00

Photo 1 above shows trap off, snake disconnected from machine and hanging out of drain.
Photo 2 shows new tool [boot] installed. Snake cable is inside and the drain is now sealed. Ready to fill other bowl and check to see if open.
Photo 3 note the support pipe to cabinet floor.

From a previous page I showed a jet assist tool... Now suppose your snaking a drain, you have taken the trap apart and have run in 3 cables should be enough footage per the piping layout. The photos below. Show a new tool I made on 1/28/2011. This tool allows you to seal off the open drain outlet leaving the snake inside. Filling the other bowl and draining to see if open properly. If not working properly, open the boot, couple on another cable and go in [down stream] further. Boot it again and try it. If open properly run water down the drain a couple of times from the second bowl. Result automatic snake washing. Note: the trap was only taken off and put back once. A little more difficult when you don't have the 2nd bowl, but you could connect a hose to the boiler drain to try the drain and wash the snake. Again this is not a tool for a stupid users !!! These tools are meant for the trade not for the inexperienced. Take notice to the support pipe, the boot does get heavy when filled.

Seminar Information (PowerPoint)

2010-07-12T08:53:00.000-04:00

My spare time recently has been spent creating a business seminar. The original is in Washington DC (I have applied for copyright registration). The seminar is called "Contracting The Why's & How's That Make It Work " It is a self timed PowerPoint Presentation. A viewer is included you do not need PowerPoint on your computer. A workbook is included, this is a "must have tool" for a trade type business. The best part is, a FREE SAMPLE. [If you click on free sample the download will have to open as read only] By viewing the sample you will be asked to do 3 math problems. Get the three right and you will not have to spend money on the seminar, you do not need it. If you don't get the right answers ... You will want to purchase the seminar. In fact when you look at the index -- even if you got the problems right, you might want the seminar.

To get a sample contact me at parrplumb@enter.net or if you found this on our web site you can click on the safe download seminar link. Your sample will be a download from Weebly.Com. By e-mail it will be sent as an attachment. Prices for the seminar are shown in the sample.

Plumbing Antiques

2008-11-19T15:10:00.000-05:00

White gas furnace -- Blow torch -- Piece of lead pipe

Trap wiped by a plumber ... I will judge some time in the 1920's or before

Still in my possession

This lead bend was removed from a property on Hamilton Street in Allentown PA. This was in a real old home of an affluent citizen. Take note to the brass threads 4" soldered into the bend. The toilet that was mounted on this pipe had a 4" brass thread cast into the china. You greased the threads and screwed the bowl onto the piping. -- A former member of the PIPDL Rod Stein (now deceased) identified this type of toilet as being made by the Mott foundry in NJ

******

The copper tube above dates back to the 1940's. Notice the little hole in the solder cup on the fitting. It was not realized that the solder would flow when heated and fill the cup. So installers in this time period had to clean the fitting and the little hole. Then the solder was added to the fitting through the hole and at the completion of the joint, the hole was filled.

More Tools Continued

2008-11-19T10:10:00.003-05:00

Above -- black tube with ball valve & hose. I used this to groute under w/pool tubs, shower bases whatever. The plug in the end had a air, quick connect. I mixed either brown coat plaster or morter cement -- filled the tube and then applied an air hose with the regulator set to 2-3 lbs. You would be surprised at what you can move with a little air behind it. The 2 pieces of wood with the all-thread rod ... This was used for undercounter lavatorys. The upper board spanned the tile, marble, granite -- whatever, the rod came through the drain hole. The bottom board spanned the bottom of the fixture, the nut with the handles was spun up the rod until tight. Now we could adjust for center and install the required clamps.

******

Disposal Stand ... Good to have when you need it.

******

H'mmmm what's this ? Up in the cold climates we sometimes have to walk on snow or ice.

This could be carrying a tool box, pulling a water heater up grade on a hand truck. When your feet slip or just slide out from under you. You could get hurt unless you have shoe chains.

More Tools

2008-11-16T08:46:00.006-05:00

In remodeling when sheets of drywall or whatever must be held these adjustable "helping hands" do just fine. The notch shown in photo #3 is so they won't slip when against studs. On a concrete floor, usually I drill a 3/16 hole and use a tapcon to keep the feet from kicking out.

******

Some Plastic Tube a heat gun and a vise makes some fancy caulk tube caps!

******

I call this "Jet Attach" Used when a kitchen drain must be jetted .

Take the fernco apart, screw the female adapter on the marvel at the drain connection in the wall. reconnect the fernco with the tee facing down. Rope comes up loops around the faucet secure with a half hitch. Under the tee put a five gallon bucket. Jetter hose now goes in the short piece and through the tee as far as you can push it. Now turn on the jetter all the water that the jetter is using flows into the bucket. As soon as the blockage is penetrated the water then flows down the pipe. This works good no mess ... unless you dump the bucket or overflow it! This is not a tool for stupid users !!!

Tools for plumbers ,,,

2008-11-15T09:55:00.002-05:00

I like to make my job easier. You might say "work smart -- not hard". Over the years I have made a lot of tools ... these are not patentable items just ideas that work. I look at this, as a little thing I once saw in "Bit's & Pieces" that was ... "If I had a penny and you had a penny and we exchanged penny's then we would still each have a penny. But if you had an idea and I had an idea and we exchanged ideas then we would each have two ideas". Now with this blog I can exchange all my ideas. Hopefully I will learn some ideas in

return. Let me say that I have been on PDL and PIPDL for about 5 years. I also spend time on a tremendous plumbers forum. About 3000 in the trade use the plumbing zone.com to keep up to date on products, problems and other items pertaining to the trade. If any members from the above listed lists are seeing this again, call it a refresher ... First an acid reversing rig. When pumping a domestic coil and the hoses are connected, this unit allows you to reverse the flow of acid without disconnecting. Works very good and believe it or not -- cuts down on the time necessary to pump as you can work inlet and outlet sides alternately. When the hoses foam because the acid got too hot and the bubbles are traveling toward the pump volute. By opening the bypass valve the resultant pump failure is stopped you don't have to re-prime. In your mind close & open the valves see how the flow changes. Hint what is open now will have to be closed and visa-versa. By-pass stays closed until needed or can be used at start to prime with all the other valves closed.

*********

Lets continue ... This tool was made for a radiant staple up job in a crawl space. Kneeling on the dirt floor my head was in the joists, could not work comfortably. Lying on a pad I could not reach the joists or the sub floor above. The Rover shown below allowed me to lay with my head just about 6" below the joists. I just rolled back & forth uncoiling and stapling as I went.

*******

Some are simple -- stop scratching ... small pieces of 5/8 heater hose over pliers jaws.

More about pliers ... When setting a pedestal lavatory the problem is to get the trap nuts tight. Pasco maybe Jones makes a wrench to fit trap nuts ... Alas, I use Wolverine Traps, the nuts are bigger and the wrench doesn't fit. A channel lock with the jaws open to fit a 1-1/4 nut -- the handle can hit the wall and mar the wall finish especially it's wall paper. My fix see the orange handle pliers below. You might have to still hold the tool on an angle but it works for me.

Yep I cut an 1-1/2" off the handle.

******

How about when you have to repair a Moen tub faucet Legend -- the balance spool is jammed. You insert a big screwdriver in the slot and the little cap comes off in your hand. Now you have a balance spool stuck inside the faucet with almost no way of grabbing it. Unless ... you have one of these in your toolbox.

Bookmark this blog there will be more ...

Interested in more tools? On the index click More Tools ...

Click on some of the other titles, also click on Seminar Information, here you are able to get a sample.

******